Supported PinView function which can help user to debug and observe pin status on a user friendly GUI. Supported one computer can be connected to 10 Nu-Link devices simultaneously. Added M452 and M453 part number for M451 series. Added part numbers: M4LEDRG6AE, M4LEDRE6AE, M4LEDLG6AE, M4LEDLE6AE. Fixed Configure Setting dialog GUI for Nano102/112 series. Supported USB Bulk mode which can improve downloading and programming speed on Win7. Provided an option to install Bulk USB driver when Nu-Link driver installation completed. Supported M0519, NM1320 and Mini58 for NuMicro M0 series. Replaced ICE clock 16 MHz with 12 MHz for compatibility issue. Increased NUC505 download speed 3 times in 1 MHz ICE clock. NUC100, M051: Supported to keep previous Config0 value after whole chip erase. Supported Mini55LDE, Mini55ZDE for NuMicro M0 series. Nano112: Fixed ICE connection failed when target chip is in Power- of 14 Rev. Mini58: Supported 2.5 KB LDROM (2 KB in previous version). NUC230/240AE: Supported 8 KB LDROM (4 KB in previous version). Supported data and conditional breakpoint functions completely. Supported breakpoint setting and memory window periodically updating while the CPU is running. If checked and downloaded code to SRAM, it will do code verification. Modified the behavior of option "memory verify code" in Debug tab. Added the selection of connect type (connect normal and connect under reset). Supported spin button edition of data flash. Updated SFR file of Mini58DE, M451 and NUC505 for register display. Supported N575, N576 and N570 for NuVoice series. Supported Nano103, NM1120, NM1330, NM1820 for NuMicro M0 series. Fixed the issue that can't find FLM path of M451 40K and N570 series. Updated SFR file of NM1120, NM1330, NM1820, Nano103 and N570 for register display. Enable SRAM access less than 0x of general chip type. Please check "NuConsole Plug-in" section of user manual in installation directory. Supported NuConsole, it can show printf log on screen via SWD interface. Supported SFR Page Selection and SPROM mapping. Added.ini file under project directory to save user configurations. Enabled secure boot option for M480 series. Added "Nuvoton Device Family Pack" of MDK5 in the installer, you must install "Nuvoton Device Family Pack" if you are using KEIL MDK Nuvoton edition. Cortex-M C51 Supported Nu-Link2 and NuTrace. Supported ML51/MS51 for NuMicro 8051 series. Added part number NUC029KGE/NUC029TAE for NuMicro M0 series. Cortex-M C51 Supported M480LD for NuMicro M4 series. Supported NUC1311, M032C/D for NuMicro M0 series. Added supported microcontroller: NuMicro M4 Family: M48x8AE, M48xCAE, M479 series and M487KMCAN. NuMicro M4 Family: M487KMCAN, M471 series. 3.03ΔΆ TABLE OF CONTENTS 1 Revision History Supported Debugger And Programmer Supported Microcontroller Resources of 14 Rev. For additional information or questions, please contact: Nuvoton Technology Corporation. All data and specifications are subject to change without notice. Nuvoton assumes no responsibility for errors or omissions. Nuvoton is providing this document only for reference purposes of NuMicro microcontroller based system design. 1 Nu-Link Driver for Keil MDK Revision History The information described in this document is the exclusive intellectual property of Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |